by RIGNOX
Sep / 20 / 2026

2007-2014 GMC Sierra 1500 & 2500HD/3500HD LED Tail Lights Installation Guide

Step-by-step RIGNOX installation guide for 2007-2013 GMC Sierra 1500 and 2007-2014 Sierra 2500HD/3500HD LED Tail Lights. Covers tools, removal, installation, the factory-style red turn signal test, and troubleshooting.

2007-2014 GMC Sierra 1500 & 2500HD/3500HD LED Tail Lights installed view

Important: This online guide is a product-image-verified overview for the matched RIGNOX product. It uses the product page, product reference images, and visible lighting-function details to guide product-side checks. Confirm hidden vehicle-side fasteners, trim clips, and wiring access points on your exact vehicle before removal.

Safety warning: Do NOT use dielectric grease or weather-sealing grease on connectors or sockets. Grease can cause connection problems and may affect warranty coverage.

Matched product

  • Product: 2007-2013 GMC Sierra 1500 & 2007-2014 Sierra 2500HD/3500HD (GMT900) LED Tail Lights
  • Product type: tail lights
  • SKU: T-SRA07-SR
  • Fitment: Fits 2007-2013 GMC Sierra 1500 and 2007-2014 GMC Sierra 2500HD / 3500HD (GMT900), all trims including Denali. Does not fit: 2007 GMC Sierra Classic.
  • Set contents: Left and right tail lamps. No adapter harness is required — the lamps plug into the factory connectors.
  • Product page: View matching RIGNOX product details

Product reference images

Use these images to compare the lamp shape, lens style and lighting functions before final assembly.

2007-2013 GMC Sierra 1500 & 2007-2014 Sierra 2500HD/3500HD (GMT900) LED Tail Lights Assembly — Pair — White Background Main Image — T-SRA07-SR
2007-2013 GMC Sierra 1500 & 2007-2014 Sierra 2500HD/3500HD (GMT900) LED Tail Lights Assembly — Pair — All Lights On Close-Up — T-SRA07-SR
2007-2013 GMC Sierra 1500 & 2007-2014 Sierra 2500HD/3500HD (GMT900) LED Tail Lights Assembly — Pair — Before and After Comparison — T-SRA07-SR
2007-2013 GMC Sierra 1500 & 2007-2014 Sierra 2500HD/3500HD (GMT900) LED Tail Lights Assembly — Pair — Running Light Close-Up — T-SRA07-SR

Product image checkpoints

  • Match the supplied connector to the vehicle connector and confirm the lock tab seats fully before closing up.
  • Brake and turn share the same red lighting zone on this product, and the turn signal flashes red. That is the intended behavior, not a fault — there is no separate amber indicator.
  • The reverse section sits low in the lamp and lights white. Confirm it against the product page images before final assembly.

Before you begin

  • Which wiring section to follow: This guide covers one build, Smoked Red (T-SRA07-SR). Follow Wiring for this kit — Smoked Red (T-SRA07-SR).
  • Confirm the exact product: Compare the RIGNOX tail lights to the product page photography, including rear housing, plug layout, and lens style.
  • Work powered down: Park on level ground, switch the truck off, and disconnect the negative battery terminal when handling wiring.
  • Protect body panels: Use clean towels or masking tape near painted edges around the tailgate and bed sides.
  • Do not force clips: If a lamp does not move, stop and look for another fastener or locating pin.
  • No grease on connectors: Do not apply dielectric grease or weather-sealing grease to connectors or sockets.

Tools and supplies

  • Trim removal tool
  • Metric socket and ratchet set; verify exact sizes on the truck before removal
  • Phillips and flat screwdrivers
  • Clean microfiber towels and masking tape
  • Electrical tape and zip ties for tidying harness routing
  • A helper for brake-light, turn-signal and reverse-light testing

Remove the original tail lights

  1. Find the fasteners: Locate the fasteners that hold the original lamp on your truck. If you cannot find them, stop and get installation help.
  2. Support the original tail light: Hold the lamp while removing its fasteners.
  3. Pull the lamp straight out: Release locating pins by pulling in line with the lamp. Do not lever against painted panels.
  4. Disconnect the wiring: Press the connector lock tab and pull by the connector body, not by the wires.
  5. Compare before fitting: Compare the removed lamp with the product page photography before fitting the new one.

Wiring for this kit — Smoked Red (T-SRA07-SR)

  • Each lamp plugs into the factory harness. No adapter is needed.
  • Compare the plug on the lamp with the factory plug before connecting. If the plug does not match, stop and get installation help with your order number and a photo of both plugs.
  • Do not cut or splice any wires.

Install the RIGNOX tail lights

  1. Pre-check the plug layout: Confirm the rear plug and mounting points match what the product page shows.
  2. Connect the lamp: Follow the wiring section above. Seat the plug fully and confirm the lock tab clicks into place.
  3. Seat the lamp evenly: Align locating pins and body gaps before tightening. Do not over-tighten plastic mounting points.
  4. Test before closing up: Run the function test below before refitting anything.

Electrical and function test

  1. Confirm running lights on both sides.
  2. Confirm brake lights with a helper pressing the brake pedal.
  3. Confirm left and right turn signals and hazards. The turn signal flashes red in the same zone as the brake light.
  4. Confirm reverse lights with the truck safely in reverse and the parking brake applied.
  5. Confirm the startup animation after the road-light functions pass.
  6. Check for dashboard warnings, hyperflash, flicker, or intermittent operation.

Final check

  • All connectors are locked, dry, and routed without tension.
  • Both lamps sit flush with even body gaps.
  • All lighting functions pass on both sides.

Troubleshooting

  • No amber turn signal: Expected. This product flashes the turn signal red in the brake zone, matching the factory lamp.
  • One function does not work: Compare the plug area to the product page photography and verify the connector is fully seated.
  • Warning message, flicker, or hyperflash: Confirm every plug is fully seated and both sides are wired the same way. If it continues, get installation help with your order number and a short video.
  • Moisture appears: Light condensation right after installation is normal and usually clears within about a week of regular driving as the lamp warms up. If water collects inside or the moisture doesn't clear, get installation help with your order number.

Need help?

If a plug, part or trim piece doesn't match this guide, stop before modifying anything and get installation help. Our install team replies within one business day and will know which guide you're following.


Updated: Nov / 09 / 2026

Before you call it done

After the Install

Fast-blinking turn signals after the swap is a load issue, not a fault, and more likely if the headlights are LED too: what to check first.

A thin mist inside the lens after a cold night is normal on any vented lamp: the automaker rule for fog vs a real leak.

Running a smoked lens and wondering about inspection? What every state actually requires.

Stuck on a step?

Our install team replies within one business day. We'll know which guide you're following. Three quick checks solve most cases; still stuck, send the photos and we'll take it from there.

Get installation help