by RIGNOX
Nov / 06 / 2026

1991-1997 Toyota Land Cruiser 80 LED Triple Projector Headlights Installation Guide

Step-by-step RIGNOX installation guide for 1991-1997 Toyota Land Cruiser 80 LED Triple Projector Headlights. Includes tools, removal, installation, function test, beam aim, and troubleshooting notes.

1991-1997 Toyota Land Cruiser 80 LED Triple Projector Headlights Installation Guide

Before you start: compare your new lights with your vehicle: the plugs, where the wiring runs and where the bolts are. If something looks different, stop and get installation help before you remove anything.

Safety warning: Do NOT use dielectric grease or weather-sealing grease on connectors or sockets. Grease can cause connection problems and may affect warranty coverage.

Matched product

  • Product: 1991-1997 Toyota Land Cruiser 80 LED Triple Projector Headlights Assembly — Pair
  • Product type: Headlights
  • SKU: H-LC80-91
  • Variants: Triple Projector
  • Fitment: 1991-1997 Toyota Land Cruiser 80 Series (FJ80 / FZJ80).
  • Product page: View matching RIGNOX product details

Product notes

  • Each side is one housing that replaces both the factory headlight and the corner lamp beside it, so you remove two lamps per side and fit one.
  • Three bi-function projectors per side handle low and high beam. A white daytime running bar runs along the bottom of the housing, switches to amber with the turn signal and sweeps outward in sequence. A startup animation runs when the lights power on.
  • The box holds one pair of headlights and two adapter cables, one per side. The adapter cable connects the headlight to your factory headlight plugs.
  • The panel at the outer end of the housing is a reflector. It does not light up.
  • Anti-flicker decoders are built into the lights.
  • The projectors and running bar are LED and built in, so there are no headlight bulbs to replace.

Before you begin

  • Check your kit: make sure the lights in the box are the version you ordered before removing your original lights.
  • Which wiring section to follow: This kit comes in one build. Follow Wiring for this kit — Triple Projector (H-LC80-91).
  • Work powered down: Park on level ground, switch the vehicle off, and disconnect the negative battery terminal when handling wiring.
  • Protect body panels: Use clean towels or masking tape around painted panels, the hood edge, and grille trim.
  • Do not force clips: If a lamp or trim panel does not move, stop and look for another fastener or locating pin.
  • No connector grease: Do not apply dielectric grease or weather-sealing grease to connectors or sockets.
  • Front-end note: Leave grille and trim loose until every lighting function passes testing and beam aim is set.

Tools and supplies

  • Trim removal tool or panel clip tool
  • Metric socket and ratchet set; confirm the exact socket sizes on your vehicle before removal
  • Phillips and flat screwdrivers
  • Clean microfiber towels and masking tape
  • Replacement plastic clips
  • Electrical tape and zip ties for securing included harnesses only
  • A helper for turn-signal testing, and a flat wall for beam aiming

Remove the original headlights and corner lamps

  1. Open front access: Open the hood and remove only the grille and trim pieces needed to reach the headlight and corner-lamp fasteners.
  2. Remove the corner lamp: Release its fasteners, disconnect its bulb socket or plug, and remove the lamp. Keep the lamp, bulb and socket until the install is finished and every function works.
  3. Support the headlight: Hold the headlight with one hand while removing the remaining fasteners.
  4. Disconnect the headlight plugs: Press each lock tab and pull by the connector body, not by the wires.
  5. Release the headlight: Draw it straight forward. Do not pry against painted body panels.
  6. Work one side at a time: Finish one side before starting the other, so the original lamps stay available as a reference.

Wiring for this kit — Triple Projector (H-LC80-91)

Back of the RIGNOX 1991-1997 Toyota Land Cruiser 80 Triple Projector headlight (H-LC80-91) showing its plug and wire leads
Adapter cable included with the RIGNOX 1991-1997 Toyota Land Cruiser 80 Triple Projector headlights (H-LC80-91), one per side
  1. Use the adapter cable: Each side uses one of the two included adapter cables. It connects the headlight to your factory headlight plugs. No cutting or splicing is needed. Each adapter cable has one large 3-pin plug and two smaller plugs.
  2. Match by shape: The large 3-pin plug of the adapter cable connects to the 3-pin plug on the back of the headlight. US-market 80 Series trucks have two factory headlight bulb plugs on each side, one for low beam and one for high beam. Compare the two smaller plugs of the adapter cable with them. Connect only plugs of the same shape, and push each one in until the lock tab clicks. Do not force a plug that does not fit.
  3. Other wire leads: The back of the housing also has separate wire leads (see the photo above). Before connecting them, get installation help with your order number, and our install team will confirm where they connect on your truck. Attach a photo of the leads and tell us where the front turn signals are on your truck (on US-market trucks they are in the front bumper, below the headlights).
  4. If anything does not match: If a plug on the lamp or the truck does not match, or you are not sure where a lead goes, stop and get installation help.

Install the RIGNOX headlights

  1. Compare before mounting: Hold the RIGNOX housing up to the opening and compare it with the original headlight and corner lamp. Transfer brackets or adjuster hardware only where the original clearly carries a part the new one does not.
  2. Connect the wiring: Follow Wiring for this kit — Triple Projector (H-LC80-91). Confirm each lock tab clicks into place.
  3. Test before mounting: Reconnect the battery and test every function (see below) while the lamp is still loose.
  4. Secure wiring: Use zip ties to keep the harness away from the hood latch, radiator support, sharp edges and heat.
  5. Seat and fasten the lamp: Align locating pins and check gaps against the hood, fender and grille before tightening. Tighten evenly without over-tightening plastic mounts.
  6. Reinstall trim last: Refit grille and trim only after testing and beam aim are done.

Electrical and function test

  1. Test low beam, high beam, the daytime running bar and the startup animation on both sides.
  2. Use the turn-signal stalk (not the hazard switch) to check each side: the bar should switch to amber and sweep outward in sequence on the correct side.
  3. Confirm there is no hyper-flash or flicker after two ignition cycles.

Set the beam aim

  1. Park square to a flat wall about 25 feet away on level ground, with a normal fuel load.
  2. Mark the height of each beam's cutoff on the wall and compare the two sides.
  3. Use the adjustment screws on each housing to bring the cutoff level and even across both sides.
  4. A projector aimed too high can dazzle oncoming drivers, so take the time to get this right.

Final check

  • All connectors are fully seated and locked.
  • The adapter cable and leads are secured away from moving parts, sharp edges, water paths and heat.
  • Both housings sit flush with even gaps, with no harness trapped behind them.
  • Every function works on both sides, and beam aim is set and even.

Troubleshooting

  • Low or high beam does not turn on: Recheck the adapter cable at both ends: the plug at the headlight and the ends at the factory connectors.
  • DRL or turn signal does not work: Recheck which plug and adapter you used. Don't cut wires or move pins: get installation help and we'll sort it out.
  • Hyper-flash or flicker: Confirm every plug is fully seated and both sides are wired the same way. If it continues, get installation help with your order number and a short video. See also LED hyperflash, flicker and bulb-out warnings.
  • Moisture appears: Light condensation right after installation is normal and usually clears within about a week of regular driving as the lamp warms up. If water collects inside or the moisture doesn't clear, contact RIGNOX support.

Need help?

If a plug, part or trim piece doesn't match this guide, stop before modifying anything and get installation help. Our install team replies within one business day and will know which guide you're following.


Updated: Nov / 18 / 2026

Before you call it done

After the Install

No DRL plug in your harness? Vehicles that never had daytime running lights need the DRL lead wired to a fuse that switches with the key: how to find the right fuse with a test light, and how to tap it safely.

Aim the low beams before you drive at night; a projector an inch too high blinds oncoming traffic: the 25-foot wall method, and where the adjusters are on this housing.

Fast-blinking turn signals or a bulb-out message after the swap is a load issue, not a fault: how to tell hyperflash from flicker, and what to check first.

A thin mist inside the lens after a cold night is normal on any vented lamp: the automaker rule for fog vs a real leak.

Stuck on a step?

Our install team replies within one business day. We'll know which guide you're following. Three quick checks solve most cases; still stuck, send the photos and we'll take it from there.

Get installation help