Before you start: compare the photos on this page with your vehicle: the plugs, where the wiring runs and where the bolts are. If something looks different, stop and get installation help before you remove anything.
Safety warning: Do NOT use dielectric grease or weather-sealing grease on connectors or sockets. Grease can cause connection problems and may affect warranty coverage.
Matched product
- Product: 1998-2005 Toyota Land Cruiser 100 LED Triple Projector Headlights Assembly — Pair
- Product type: Headlights
- SKU: H-LC100-98
- Variants: Triple Projector (one build)
- Fitment: 1998-2005 Toyota Land Cruiser 100 Series (J100). Does not fit Lexus LX470, which uses different mounting and a factory leveling motor.
- Product page: View matching RIGNOX product details
Product reference images
Use these images to compare the lamp shape, rear housing, visible plug layout, and lighting functions before final assembly.




Product notes
- Three projector cups per side: two bi-function for low and high beam, one dedicated low beam, plus a white DRL bar the width of the housing.
- When you signal, the white DRL bar turns amber and works as the turn signal, sweeping outward in sequence.
- There is no amber side marker or side reflector on this housing. With the parking lights on, the white DRL bar lights as the parking light, so the amber glow of the factory side marker goes away. This is normal, not a fault.
- At power-on the housing runs a blue startup sweep before the bar settles into white. It plays once, at a standstill, and takes no part in the road beam.
- This assembly covers the 1998-2005 Land Cruiser 100 with factory halogen headlights. The 2006-2007 truck uses a different headlight, so go by model year.
- The headlights plug into the factory harness. CANbus decoders are built in.
- Each housing has adjustment screws to set the beam height.
- On a truck of this age, expect grille and headlight-surround clips to have gone brittle. Have replacement clips on hand before starting.
Before you begin
- Confirm the exact product: Check your kit SKU against the list above before removing original parts.
- Which wiring section to follow: This product has one build. Follow Wiring for this kit — Triple Projector (H-LC100-98).
- Work powered down: Park on level ground, switch the vehicle off, and disconnect the negative battery terminal when handling wiring.
- Protect body panels: Use clean towels or masking tape around painted panels, the hood edge, and grille trim.
- Do not force clips: If a lamp or trim panel does not move, stop and look for another fastener or locating pin.
- No connector grease: Do not apply dielectric grease or weather-sealing grease to connectors or sockets.
- Front-end note: Leave grille and bumper trim loose until every lighting function passes testing and beam aim is set.
Tools and supplies
- Trim removal tool or panel clip tool
- Metric socket and ratchet set; confirm the exact socket sizes on your vehicle before removal
- Phillips and flat screwdrivers
- Clean microfiber towels and masking tape
- Replacement plastic clips
- Electrical tape and zip ties for securing included harnesses only
- A helper for turn-signal testing, and a flat wall for beam aiming
Remove the original headlights
- Open front access: Open the hood and remove only the grille trim, upper bumper fasteners, and access covers required to reach the headlight fasteners.
- Expose lamp fasteners: Release clips with a trim tool rather than a screwdriver. Work slowly and confirm each fastener before pulling.
- Support the lamp: Hold the headlight with one hand while removing the remaining bolts or clips.
- Disconnect vehicle connectors: Press each lock tab and pull by the connector body, not by the wires.
- Release locating pins: Draw the headlight straight forward. Do not pry against painted body panels.
- Repeat on the opposite side: Complete one side fully before starting the other, so the original assembly stays available as a reference.
Wiring for this kit — Triple Projector (H-LC100-98)
- Plug-and-play: The headlights plug into the factory headlight harness. No cutting or splicing is needed.
- Decoders: CANbus decoders are built in. Anything needed to prevent hyperflash and dash warnings is built into the light or packed in the box. If your box includes a decoder or adapter, connect through it.
- Match each plug: Plug each connector on the back of the headlight into the factory connector it matches. Push until the lock tab clicks, then pull gently to confirm it holds.
- Do not force a plug: If a connector does not fit, stop. Take clear photos of the headlight plugs and the vehicle plugs, then get installation help.
Install the RIGNOX headlights
- Compare assemblies before mounting: Compare the removed original and the RIGNOX headlight. Transfer brackets, seals, or adjuster hardware only where the original clearly carries a part the new one does not.
- Connect the main harness: Connect the plugs as shown in Wiring for this kit and confirm each lock tab clicks into place.
- Secure wiring before mounting: Use zip ties to prevent rubbing, pinching, water pooling, or contact with the hood latch, radiator support, and exhaust heat.
- Seat and fasten the lamp: Align locating pins and check panel gaps against the hood, fender, and grille before tightening. Tighten evenly without over-tightening plastic mounts.
- Reinstall trim last: Leave grille and bumper trim loose until every electrical function passes testing and beam aim is set.
Electrical and function test
- Test daytime running lights, low beam, high beam, left and right turn signals, hazards, and the startup animation.
- Switch on the parking lights and confirm the white DRL bar lights on both sides. There is no amber side marker on this housing, so no amber light comes on at the corner.
- Confirm the DRL bar turns amber and sweeps outward when you signal, on the correct side.
- Check all three projectors on each side on low beam, then on high beam.
- Confirm no hyperflash or flicker appears after two ignition cycles.
- After all tests pass, reinstall grille and bumper trim and confirm no wire is stretched or pinched.
Set the beam aim
- Park square to a flat wall about 25 feet away on level ground, with a normal fuel load and no unusual weight in the trunk or cargo area.
- Mark the height of each beam center on the wall and compare the two sides.
- Use the adjustment screws on each housing to bring the cut-off line level and even across both sides.
- This step matters here because the vehicle is moving to a projector with a sharp cut-off. A projector aimed too high is worse for oncoming traffic than the lamp it replaced.
Final check
- All connectors are fully seated and locked.
- All included harnesses and adapters are secured away from movement, sharp edges, water paths, and heat sources.
- Both lamps sit flush with even body gaps and no trapped harness behind the assembly.
- All headlight functions test correctly on both sides with a helper operating the controls.
- Beam aim is set and even.
- No warning lights, hyperflash, flickering, abnormal heat, moisture entry, or loose modules remain after a short function check.
Troubleshooting
- One headlight does not turn on: Recheck the main connector on that side and the corresponding fuse.
- Warning, flicker, or hyperflash appears: Confirm every connector is fully seated, and that any decoder or adapter from the box is connected, before assuming a fault in the assembly.
- Some projectors stay dark, but the turn signal and startup animation work: Turn the vehicle off and recheck that every plug on the back of that headlight is fully seated. If it is still the same, do not open the housing. Contact us with your order number and a short video showing which projectors light on low beam and on high beam, and our team will tell you the next step.
- A connector does not fit: Do not force or modify it. Send photos of the headlight plug and the vehicle plug with your order number, and our team will help you match them.
- Moisture inside the lens after install: A little moisture right after install is normal. It usually clears with regular use within about a week, and can return for a few days after a car wash, rain, or a big temperature swing. If it is still there after a week, contact us with your order number.
- Trim will not sit flush: Check for a trapped harness, a broken or missing clip, or a locating pin that has not seated.
- Beam pattern looks uneven: Recheck aim against a flat wall before adjusting anything else.
Need help?
If a plug, part or trim piece doesn't match this guide, stop before modifying anything and get installation help. Our install team replies within one business day and will know which guide you're following.
Explore more for this vehicle
Shop all Toyota Land Cruiser Headlights for related fitment options and styles, or see the Toyota Land Cruiser Tail Lights that match.
