by RIGNOX
Sep / 22 / 2026

2012-2015 Toyota Prius LED Projector Headlights Installation Guide

Step-by-step RIGNOX installation guide for the 2012-2015 Toyota Prius LED projector headlights, in Dual Projector and Triple Projector builds. Covers tools, removal, installation, function test and troubleshooting.

2012-2015 Toyota Prius LED Projector Headlights installed view

Important: This online guide is a product-side overview for the matched RIGNOX product. Confirm hidden vehicle-side fasteners, trim clips, and wiring access points on your exact vehicle before removal.

Safety warning: Do NOT use dielectric grease or weather-sealing grease on connectors or sockets.

Matched product

  • Product: 2012-2015 Toyota Prius (XW30) LED Projector Headlights
  • Product type: headlights
  • SKU: H-PRI12-D (Dual Projector) / H-PRI12-T (Triple Projector)
  • Fitment: Fits 2012-2015 Toyota Prius (XW30 liftback) with factory halogen headlights. Does not fit cars with factory LED headlights, Prius Plug-in, Prius c or Prius v.
  • Set contents: Left and right headlight assemblies.
  • Product page: View matching RIGNOX product details

Product reference images

Use these images to compare the lamp shape, lens layout and lighting functions before final assembly. The first four images show the Dual Projector build (H-PRI12-D). The last image shows the Triple Projector build (H-PRI12-T).

2012-2015 Toyota Prius (XW30) LED Projector Headlights Assembly — Pair — Pair on white background — H-PRI12-D
2012-2015 Toyota Prius (XW30) LED Projector Headlights Assembly — Pair — All lights on close-up — H-PRI12-D
2012-2015 Toyota Prius (XW30) LED Projector Headlights Assembly — Pair — Before and after headlight comparison — H-PRI12-D
2012-2015 Toyota Prius (XW30) LED Projector Headlights Assembly — Pair — White DRL close-up — H-PRI12-D
2012-2015 Toyota Prius (XW30) LED Triple Projector Headlights, pair on white background — H-PRI12-T

Before you begin

  • Confirm your Prius: These fit the 2012-2015 Prius liftback with factory halogen headlights. They do not fit the Prius Plug-in, Prius c or Prius v.
  • Confirm the build you received: two projector cups per side is the Dual build (H-PRI12-D), three is the Triple build (H-PRI12-T). Both fit the same way.
  • Which wiring section to follow: Both builds use the same section. Follow Wiring for this kit — Dual / Triple Projector (H-PRI12-D / H-PRI12-T).
  • Work powered down: park on level ground, switch off, and disconnect the negative battery terminal when handling wiring.
  • Protect body panels: tape the painted edges around the bumper cover and fender before removal.
  • Do not force clips: if a lamp, bumper cover or trim panel does not move, stop and look for another fastener.
  • No grease on connectors.

Tools and supplies

  • Trim removal tool or panel clip tool
  • Metric socket and ratchet set; verify sizes on the vehicle before removal
  • Phillips screwdriver
  • Clean microfiber towels and masking tape
  • A wall or flat vertical surface for beam-pattern checking

Remove the original headlights

  1. Reach the headlight fasteners: remove only the fasteners, clips and trim needed to reach the headlight mounts on your Prius.

  2. Unbolt the headlight and support it as the last fastener comes out.

  3. Disconnect the wiring: press each lock tab and pull on the connector body, not on the wires.

  4. Compare before fitting: hold the RIGNOX lamp against the original and confirm mounting tabs and plug position.

Wiring for this kit — Dual / Triple Projector (H-PRI12-D / H-PRI12-T)

These headlights plug into the factory harness. No cutting or splicing.

  • Plug each RIGNOX connector into the matching factory connector. Push until the lock tab clicks.
  • Compare each plug with the photo below. If a plug does not match your factory connector, stop and get installation help.
  • The Dual and Triple builds use the same set of plugs (two gray and two black), so the photo below applies to both.
  • The two black plugs are bulb-style plugs for the car's low-beam and high-beam bulb connectors. The two gray plugs go to the remaining factory connectors. Match each one by shape.
2012-2015 Toyota Prius (XW30) LED Projector Headlights — rear housing and connector detail, Dual Projector build H-PRI12-D

The lens functions are shown below: the projector cups give low and high beam, and the light bar is the DRL and turn signal.

2012-2015 Toyota Prius (XW30) LED Projector Headlights — function identification: low beam and high beam projectors, DRL / turn signal light bar — H-PRI12-D

Install the RIGNOX headlights

  1. Connect the lamp to the factory connectors, as shown in Wiring for this kit. Confirm each lock tab clicks home.

  2. Test before closing up: confirm low beam, high beam, the white daytime running light, the sequential amber turn signal and the startup animation.

  3. Seat and bolt the lamp, checking the gap against the fender, hood and bumper cover before tightening.

  4. Refit any trim you removed, then repeat on the opposite side and reconnect the negative battery terminal.

Electrical and function test

  1. Confirm low beam and high beam on both sides.
  2. Confirm the white daytime running light on both sides.
  3. With the lights on, confirm the amber side marker at the outer corner lights on both sides.
  4. Confirm the turn signals and hazards: the white DRL switches to amber and sweeps outward in sequence.
  5. Confirm the startup animation at power-on.
  6. Check for dashboard warnings, flicker or hyperflash.
  7. Verify beam aim against a flat vertical surface.

Troubleshooting

  • One lamp does not light: recheck the connector lock, the related fuse and the battery connection.
  • Hyperflash or a dash warning: Confirm every plug is fully seated and both sides are wired the same way. If it continues, get installation help with your order number and a short video.
  • Body gaps look uneven: recheck that all trim and clips are fully re-seated before adjusting the lamp itself.
  • Moisture appears: Light condensation right after installation is normal and usually clears within about a week of regular driving as the lamp warms up. If water collects inside or the moisture doesn't clear, contact RIGNOX support with your order number.

Need help?

Contact RIGNOX support with your order number and your vehicle's year, model and trim. We'll walk you through it.


Updated: Nov / 17 / 2026

Before you call it done

After the Install

No DRL plug in your harness? Vehicles that never had daytime running lights need the DRL lead wired to a fuse that switches with the key: how to find the right fuse with a test light, and how to tap it safely.

Aim the low beams before you drive at night; a projector an inch too high blinds oncoming traffic: the 25-foot wall method, and where the adjusters are on this housing.

Fast-blinking turn signals or a bulb-out message after the swap is a load issue, not a fault: how to tell hyperflash from flicker, and what to check first.

A thin mist inside the lens after a cold night is normal on any vented lamp: the automaker rule for fog vs a real leak.

Stuck on a step?

Our install team replies within one business day. We'll know which guide you're following. Three quick checks solve most cases; still stuck, send the photos and we'll take it from there.

Get installation help