Important: This online guide is a product-side overview for the matched RIGNOX product. Confirm hidden vehicle-side fasteners, trim clips, and wiring access points on your exact vehicle before removal.
Safety warning: Do NOT use dielectric grease or weather-sealing grease on connectors or sockets.
Matched product
- Product: 2019-2025 Toyota RAV4 (XA50) LED Triple Projector Headlights
- Product type: headlights
- SKU: H-RAV4-20
- Fitment: Fits 2019-2025 Toyota RAV4 (XA50) — gas, Hybrid and Prime — without the factory AFS adaptive front-lighting system.
- Set contents: Left and right headlight assemblies, plus two adapter harnesses — one for the higher trims and one for the mid and base trims.
- Product page: View matching RIGNOX product details
Product reference images
Use these images to compare the lamp shape, rear housing, visible plug layout, and lighting functions before final assembly.





Before you begin
- Confirm your RAV4: These fit the 2019-2025 RAV4 (XA50) — gas, Hybrid and Prime. They do not fit a RAV4 that left the factory with AFS adaptive headlights.
- Identify the three circuits first: high / low beam, turn signal and DRL. Choose the appropriate supplied beam adapter and the matching turn-signal and DRL plugs for your vehicle version. The unused connector options remain disconnected.
- Which wiring section to follow: This kit has one build. Follow Wiring for this kit — Triple Projector (H-RAV4-20).
- Work powered down: park on level ground, switch off, and disconnect the negative battery terminal when handling wiring.
- Protect body panels: tape the painted edges around the bumper cover, fender and hood line.
- Do not force clips: if a lamp or trim panel does not move, stop and look for another fastener.
- No grease on connectors.
Tools and supplies
- Trim removal tool or panel clip tool
- Metric socket and ratchet set; verify sizes on the vehicle before removal
- Phillips screwdriver
- Clean microfiber towels and masking tape
- Zip ties for securing the adapter harness
- A wall or flat vertical surface for beam-pattern checking
Remove the original headlights
Reach the headlight fasteners: remove only the fasteners, clips and trim needed to reach the headlight mounts on your RAV4.
Unbolt the headlight and support it as the last fastener comes out.
Disconnect the wiring: press each lock tab and pull on the connector body, not on the wires.
Compare before fitting: hold the RIGNOX lamp against the original and confirm mounting tabs and plug position.
Wiring for this kit - Triple Projector (H-RAV4-20)
There are three circuits to connect on each side: high / low beam, turn signal and DRL. Choose the matching connector option for your vehicle version. The remaining unused plugs do not need to be connected.

- High / low beam: choose the appropriate adapter from the two options supplied. Connect its headlight end to the black high / low beam plug on the lamp. At the vehicle end, connect the plugs that match the factory connections and leave the other options unused.
- Turn signal: choose one of the two turn-signal plugs that matches your vehicle version.
- DRL: choose one of the two DRL plugs that matches your vehicle version.
- Polarity: check that positive (+) and negative (-) correspond correctly for all three circuits: high / low beam, turn signal and DRL. If you cannot confirm the connection, stop and get installation help. Do not force plugs or cut wires.


Leave the unused plugs disconnected, secured and protected from water and accidental contact. Compare the connector layout with your vehicle; do not identify the correct connection by wire color alone.
Test before mounting: after completing the wiring and polarity checks on both sides, reconnect the negative battery terminal. Test low beam, high beam, left and right turn signals separately, hazards and DRLs. Secure the lamps and reinstall trim only after all functions pass.
Install the RIGNOX headlights
Connect the lamp to your factory connectors through the matching adapter harness, as shown in Wiring for this kit. Confirm each lock tab clicks home.
Test before closing up: after completing the connections and checking polarity on both sides, reconnect the negative battery terminal. Confirm low beam, high beam, the white daytime running light with its blue accent, the sequential amber turn signal and the startup animation.
Seat and bolt the lamp, checking the gap against the fender, hood and bumper cover before tightening.
Secure the adapter harness with zip ties away from heat, moving parts, water paths and sharp edges, then refit any trim you removed.
Check both sides and secure the lamps only after all electrical functions pass.
Electrical and function test
- Confirm low beam and high beam on both sides.
- Confirm the white daytime running light with its blue accent on both sides.
- Test left and right turn signals separately with the turn-signal stalk, then test the hazards: the DRL switches to amber and sweeps outward in sequence.
- Confirm the startup animation at power-on.
- With the lights on, confirm the amber side marker at the outer corner lights on both sides.
- Check for dashboard warnings, flicker or hyperflash.
- Verify beam aim against a flat vertical surface. Aim with the adjusting screws on each headlight: up/down, plus left/right if your factory headlight has it.
Troubleshooting
- Low / high beam does not work: recheck the black headlight plug, the selected adapter and the matching vehicle-side plugs.
- Turn signal does not work: recheck which of the two turn-signal connector options is in use, that it is seated at both ends, and that its positive and negative connections correspond.
- DRL does not work: recheck the selected DRL connector option, seating and polarity. Switch the ignition and lights off and disconnect the negative battery terminal before changing wiring. If the issue remains, get installation help before final assembly.
- Hyperflash or a dash warning: Confirm every plug in use is fully seated and both sides use the matching connections for the vehicle version. Leave unused connector options disconnected. If it continues, get installation help with your order number and a short video.
- The lamp will not sit flush: check for a trapped harness behind the housing rather than forcing the bolts.
- Moisture appears: Light condensation right after installation is normal and usually clears within about a week of regular driving as the lamp warms up. If water collects inside or the moisture doesn't clear, contact RIGNOX support with your order number.
Need help?
Contact RIGNOX support with your order number and your vehicle's year, model and trim. We'll walk you through it.
Explore more for this vehicle
Shop all Toyota RAV4 Headlights for related fitment options and styles.
