Before you start: compare the photos on this page with your vehicle: the plugs, where the wiring runs and where the bolts are. If something looks different, stop and get installation help before you remove anything.
Safety warning: Do NOT use dielectric grease or weather-sealing grease on connectors or sockets. Grease can cause connection problems and may affect warranty coverage.
Matched product
- Product: 2016-2023 Toyota Tacoma (3rd Gen) LED Quad Projector Headlights Assembly — Pair
- Product type: Headlights
- SKU: H-TAC16-Q
- Variant: Quad Projector
- Fitment: Fits 2016-2023 Toyota Tacoma (3rd Gen) with factory halogen headlights. Does not fit trucks with factory LED headlights.
- Product page: View matching RIGNOX product details
Product notes
- Four LED projectors per side, with a C-shaped white daytime running light and an amber corner marker.
- When you signal, the white daytime light switches to amber and sweeps outward in sequence. A startup animation runs when the lights power on.
- Both adapter harnesses come in the box: one for halogen headlights with the factory LED daytime light, one for halogen headlights without it. You use one of them, depending on your truck.
- Everything needed to prevent hyper-flash and dash warnings is built into the light or packed in the box. Installation is plug-in, with no cutting or splicing.
- This set is for trucks with factory halogen headlights only. It does not fit trucks that came with factory LED headlights.
Wiring reference photos
Use these photos to identify the lamp leads, both adapter harnesses and the fuse tap before you connect anything.


Before you begin
- Confirm your headlights are halogen: Look at the original headlights before buying tools or removing anything. If your truck came with factory LED headlights, this set will not fit: stop and get installation help.
- Check whether your original headlights have the LED daytime light strip: This decides which adapter harness you use. With the strip: follow Wiring — halogen with the factory LED daytime light. Without the strip: follow Wiring — halogen without the factory LED daytime light.
- Check the box: Left and right headlight assemblies, two adapter harnesses (one for each factory setup above), load resistors, and the fuse tap used on trucks without the factory LED daytime light. If a part you need is missing, stop installation.
- Check your kit: make sure the lights in the box are the version you ordered before removing your original lights.
- Work powered down: Park on level ground, turn off the engine, and disconnect the negative battery terminal before handling wiring.
- Protect body panels: Use clean towels or masking tape around painted panels, the hood edge, and grille trim.
- Inspect mounts and do not force clips: Check both new lamps for cracked or broken mounting tabs before removing the originals. If a bracket is damaged, stop and contact support. If a lamp or trim panel does not move, stop and look for another fastener or locating pin.
- No connector grease: Do not apply dielectric grease or weather-sealing grease to connectors or sockets.
- Front-end note: Leave grille and bumper trim loose until every lighting function passes testing and beam aim is set.
Tools and supplies
- Trim removal tool or panel clip tool
- Metric socket and ratchet set; confirm the exact socket sizes on your vehicle before removal
- Phillips and flat screwdrivers
- Fuse puller (trucks without the factory LED daytime light)
- Clean microfiber towels and masking tape
- Replacement plastic clips
- Electrical tape and zip ties for securing included harnesses only
- A helper for turn-signal testing, and a flat wall for beam aiming
Remove the original headlights
- Open front access: Open the hood and remove only the grille, upper bumper fasteners, and access covers required to reach the headlight fasteners.
- Expose lamp fasteners: Release clips with a trim tool rather than a screwdriver. Work slowly and confirm each fastener before pulling.
- Support the lamp: Hold the headlight with one hand while removing the remaining bolts or clips.
- Disconnect vehicle connectors: Press each lock tab and pull by the connector body, not by the wires.
- Release locating pins: Draw the headlight straight forward. Do not pry against painted body panels.
- Repeat on the opposite side: Complete one side fully before starting the other, so the original assembly stays available as a reference.
Wiring — halogen with the factory LED daytime light

- Pick the right harness: Use the adapter harness shown above. The other harness, with the separate red lead, is not used on this setup.
- Connect the adapter to the truck: Match the gray plugs on the adapter to the original vehicle-side headlight connectors by shape and locking tab. Push each one in until the lock clicks.
- Connect the adapter to the lamp: Match the low beam, high beam and DRL leads on the lamp to the matching plugs on the adapter, using the labels on the lamp leads. Seat every lock.
- Load resistor: Plug in the load resistor where the wiring photos show it. It is plug-in, with no cutting or splicing.
- Stop condition: If a plug does not match the photos or will not lock without force, stop and get installation help. Do not cut wires, move pins or force a connection.
Wiring — halogen without the factory LED daytime light


- Pick the right harness: Use the adapter harness with the separate red lead, shown above.
- Connect the adapter to the truck and the lamp: Match the gray plugs to the original vehicle-side connectors, then match the low beam, high beam and DRL leads on the lamp to the adapter. Seat every lock.
- Find a switched (ACC) fuse: The red lead needs power that turns on and off with the ignition. Use a fuse slot that only has power with the key on. Check the fuse box lid or your owner's manual, and confirm with a test light if you have one. If you are unsure which slot is switched, stop and get installation help.
- Check the fuse type: The included fuse tap is the low-profile mini type. Make sure it matches the fuses in the fuse box you plan to use before you pull a fuse.
- Install the fuse tap: Pull the switched fuse, fit it into the fuse tap as shown in the photo, and plug the fuse tap into that slot. Connect the red lead from the adapter to the fuse tap lead.
- Route the red lead: Run it along existing wiring to the fuse box and secure it with zip ties, away from the hood latch, radiator support and hot parts.
- Load resistor: Plug in the load resistor where the wiring photos show it. It is plug-in, with no cutting or splicing.
- Never connect the red lead directly to the battery. The daytime light would stay on with the truck off and drain the battery.
- Stop condition: If a plug does not match the photos, the fuse tap does not fit your fuse box, or a part is missing, stop and get installation help. Do not cut wires, move pins or force a connection.
Install the RIGNOX headlights
- Compare assemblies before mounting: Compare the removed original and the RIGNOX headlight. Transfer brackets, seals, or adjuster hardware only where the original clearly carries a part the new one does not.
- Connect the wiring: Follow the wiring section for your truck above.
- Test before you mount: Reconnect the battery and run the function test below with the lamp still loose.
- Secure wiring before mounting: Use zip ties to prevent rubbing, pinching, water pooling, or contact with the hood latch, radiator support, and hot parts.
- Seat and fasten the lamp: Align locating pins and check panel gaps against the hood, fender, and grille before tightening. Tighten evenly without over-tightening plastic mounts.
- Reinstall trim last: Leave grille and bumper trim loose until every electrical function passes testing and beam aim is set.
Electrical and function test
- Test daytime running lights, low beam, high beam, left and right turn signals, and the startup animation.
- Use the turn-signal stalk, not the hazard switch, and confirm the white daytime light turns amber and sweeps outward on the correct side.
- Trucks without the factory LED daytime light: switch the ignition off and confirm the daytime light goes off with it.
- Confirm no hyper-flash or flicker appears after two ignition cycles.
- After all tests pass, reinstall grille and bumper trim and confirm no wire is stretched or pinched.
Set the beam aim
- Park square to a flat wall about 25 feet away on level ground, with a normal fuel load and no unusual weight in the bed.
- Mark the height of each beam center on the wall and compare the two sides.
- Use the adjustment screws on each housing to bring the cutoff line level and even across both sides.
- This step matters because projectors have a sharp cutoff. A projector aimed too high is worse for oncoming traffic than the lamp it replaced.
Final check
- All connectors are fully seated and locked.
- All included harnesses, resistors and the fuse tap lead are secured away from movement, sharp edges, water paths, and heat sources.
- Both lamps sit flush with even body gaps and no trapped harness behind the assembly.
- All headlight functions test correctly on both sides with a helper operating the controls.
- Beam aim is set and even.
- No warning lights, hyper-flash, flickering, or loose harnesses remain after a short function check.
Troubleshooting
- One headlight does not turn on: Recheck the plugs on that side and the corresponding fuse.
- Daytime light does not come on (trucks without the factory LED daytime light): Check the red lead connection at the fuse tap, that the fuse tap is fully seated, and that the slot you picked has power with the key on.
- Daytime light stays on with the truck off: The fuse slot you picked has constant power. Move the fuse tap to a switched (ACC) slot.
- Functions are mixed up: recheck which plug and adapter you used against the photos on this page. Don't cut wires or move pins: get installation help and we'll sort it out.
- Hyper-flash or a dash warning appears: Confirm the load resistor is plugged in and every connector is fully seated.
- Moisture inside the lens: Light condensation right after installation is normal and usually clears within about a week of regular driving as the lamp warms up. If water collects inside or the moisture doesn't clear, contact RIGNOX support.
- Trim will not sit flush: Check for a trapped harness, a broken or missing clip, or a locating pin that has not seated.
- Beam pattern looks uneven: Recheck aim against a flat wall before adjusting anything else.
Need help?
If a plug, part or trim piece doesn't match this guide, stop before modifying anything and get installation help. Our install team replies within one business day and will know which guide you're following.
Explore more for this vehicle
Shop all Toyota Tacoma Headlights for related fitment options and styles, or see the Toyota Tacoma Tail Lights that match.
